How To Change Thd Fuel Filter On A Murry Single Stage Snow Blower

These instructions volition explain how to prepare your snow thrower for off-season storage. Some of these steps differ betwixt single-, 2- and 3-stage snow throwers. Depending on your model, the instructions below may also vary slightly from what is outlined in your operator's manual. Ever refer to your operator's manual for comprehensive instructions on maintenance and storage.

INSTRUCTIONS:

Step 1 - Prepare your snowfall blower for maintenance.

Identify your snow blower on a flat surface. Turn the engine off and let it cool. Disconnect the spark plug ignition wire and remove the safety ignition key to forbid accidental starting of the engine.

Single-Stage Snowfall THROWER STORAGE MAINTENANCE (STEPS ii – 6)

Step 2 - Position the snow thrower for maintenance.

Advisedly tilt the snow thrower back and so information technology rests on the handle. This will permit you to easily access various components.

Pace 3 - Cheque the shave plate.

The shave plate can article of clothing out over fourth dimension. The shave plate on your snow thrower has two wearing edges, only contrary information technology to maximize the life of the plate. If it's already been reversed, replace it with genuine, original equipment part from Cub Buck.

Step iv - Cheque the auger.

The auger'south condom paddles become worn with use. They should be replaced if any excessive wear is nowadays.

Step v - Audit the chugalug.

Remove the belt embrace on the side of the snow thrower. Bank check the chugalug for signs of wear, cracks, fraying, etc. and supercede if necessary

Step 6 - Gild replacement parts.

If any of the items mentioned above need replacing at the end of the season, information technology's a adept time to lodge and install them before you lot put your snow thrower into storage.

Two- AND THREE-Stage Snowfall THROWER STORAGE MAINTENANCE (STEPS two – 6)

Footstep 2 - Check the shave plate.

Cheque the shave plate and slip shoes for damage and wear. The shave plate and skid shoes protect the housing from damage. Replace these items with genuine, original equipment parts from Cub Buck.

Pace 3 – Position the snow thrower for maintenance.

Bleed whatsoever fuel left in the tank using the siphon pump. A siphon pump tin be purchased on cubcadet.com and wherever mower parts are sold. With the aid of another person, carefully pivot the snow thrower upwardly and frontward then it rests on the auger housing. This volition let you to hands access the parts of the snow thrower that require maintenance.

Step 4 - Lubricate the gear shaft.

Remove the lower frame embrace from the underside of the unit. Apply a low-cal coating of oil to the hex shaft. Be conscientious not to become whatever oil on the aluminum bulldoze plate or the safe friction disc. Cheque the prophylactic friction disc for wear or keen.

Footstep 5 - Return the snow thrower to its wheels and skid shoes

Before checking the snowfall thrower belt, put the lower frame cover back in place. With the help of an boosted person, carefully pivot the snow thrower back and down and then information technology rests on the wheels and skid shoes.

Pace half-dozen - Inspect the belt

Remove the chugalug cover on the front of the engine and inspect the belts for wear, cracks and fraying. If the belts are worn, they should be replaced immediately. Worn belts can intermission when you least wait it so make certain yous replace your snow thrower chugalug every bit soon as you see signs of wear. Put the plastic chugalug cover back in place or society a new ane if needed.

SINGLE-, Two- AND THREE-Stage Snow THROWER STORAGE MAINTENANCE (STEPS 7 – 10)

Step 7 - Change the oil.

Bleed and refill the engine oil earlier storing your snowfall thrower. Refer to your engine's Operator's Manual for the correct viscosity and oil capacity. Always dispose of the used oil in an environmentally responsible manner.

Step 8 - Check the spark plug.

Remove the spark plug and inspect it for signs of corrosion or residue build-up. Clean information technology with a wire brush if necessary. If you are unsure if the spark plug is good or not, it is recommended that y'all supersede the spark plug. Reinstall the spark plug and reconnect the spark plug ignition wire.

Step 9 - Clean the snow thrower.

Clean droppings from around the engine and muffler. Apply a low-cal pic of oil on any areas that are susceptible to rust. Wipe away any dried salt that may have accumulated to help prevent your unit from rusting over the winter.

Footstep ten - Prepare the fuel tank.

Finally, fill up your engine's fuel tank with fresh gasoline and add together a fuel stabilizer. This is better than storing it empty considering an empty fuel system exposes any bare metal parts within it to air and moisture - which tin can pb to rust and allows gaskets and O-rings to dry out, scissure and shrink, causing eventual leaks.

Following these steps for proper snow thrower storage will help ensure you have a well-operation machine the next winter. Remember to consummate each of the steps outlined above, skipping a snowfall thrower storage maintenance procedure can outcome in expensive repairs downward the road. For more snowfall thrower maintenance tips, check out our Cub Cadet how-to articles.

Cub Cadet Genuine Parts

E'er utilise genuine OEM replacement parts when servicing your equipment. Use our parts finder to locate and order any replacement parts yous may need for maintenance. Refer to your owner'south manual for additional maintenance information.

Source: https://www.cubcadet.com/en_US/knowledge-center/knowledge-how-to-prepare-your-snow-thrower-for-storage-in-the-off-season.html

Posted by: stubbslieuphe.blogspot.com